imagen

ADJUVANTS

Multi action adjuvants are additives developed to give the producer, chemical stability of the formulation and multiple physicochemical properties in a single product that contribute to improve the application and bioavailability of the active ingredient and the possibility of using them with a wide spectrum of chemical products in different climatic conditions and crops.

imagen
SpeedWet Xion Activegel it is a high concentration multi-action adjuvant for the application of pre-emergent herbicides and graminicides. Conditioning, humidification and penetration.
imagen
GENERAL
imagen

The specific and balanced combination of new surfactants, humectants and water conditioners, added to the accelerating power, allow SpeedWet Xion Activegel to concentrate the action in a lower dose, managing to minimize chemical, physical and environmental barriers in order for the herbicide to express to its full potential.

Conditioning:

Herbicides such as glyphosate and many pyrethroid insecticides are sensitive to the reaction of water and, in most cases, an ideal value is between pH 4 and 6. SpeedWet Xion Activegel gel conditions the water, providing the ideal (slightly acidic) medium for that these phytosanitary agents act optimally.

Simultaneously, its innovative formula complexes the salts that interfere with many phytosanitary agents, increasing its activity at the site of action.

Wetting and penetration

When the spray droplets settle on the surface of the leaves, they face a series of barriers that limit the absorption of the transported pesticide. The hairiness and the waxy layer become the main obstacles for the entry of the chemical in the plant.

The complex of surfactants in SpeedWet Xion Activegel formulation gives a superior moisturizing capacity, leading to a more efficient penetration of the transported phytosanitary.

Other properties

Controls the foam production and protects the broth against the effects of evaporation.

IMPORTANT
imagen

Always incorporate SpeedWet Xion at the beginning of the charging process so that acidifying agents, sequestrants and foam inhibitors work.

Keep the agitation or return system running for greater homogenization.

Respect the order of loading of the plant protection products to be used.

INSTRUCTIONS FOR USE
imagen
Preparation: add SpeedWet Xion Activegel at the beginning of the tank load (1/4 capacity), complete the tank load and add the products.

INSTRUCTIONS FOR USE

In herbicide applications (hormonal, contact, systemic, desiccant, gramicide).

DOSE

50 - 75 cm3 / 100 liters of water

imagen FOLLETO SpeedWet Xion Activegel
imagen
SpeedWet Xion Silicongel it is a more concentrated multi-action adjuvant with the exact balance of assets designed for new application technologies.
imagen
GENERAL
imagen

SpeedWet Xion Silicongel is the result of a long research and development process aimed at carefully identifying the properties necessary to ensure the bioavailability of insecticides and fungicides, under different environmental and application conditions, even the most extreme.
SpeedWet Xion Silicongel is a more concentrated and accurately balanced active compounding formulation aid for new application technologies.

The surfactants present in the formulation act together with the fatty amides, providing key properties for the application of fungicides and insecticides. Together, these properties work synergistically and allow for a more uniform drop spray, with better penetration in canoeing and protected from the effects of high temperatures and low relative humidity conditions.

Drop size, uniformity and anti-evaporation

Choosing the right droplet size results from a compromise between the difficulty of the treatment and the prevailing environmental conditions. More demanding coverage treatments require smaller droplet sizes to penetrate their leaf mass, but as we reduce the size we make the broth more prone to evaporation and drift losses. This is why SpeedAgro has devoted many resources to developing a formulation with the exact balance of surfactants and fatty amides so that the spray breaks evenly and the resulting droplet travels protected towards the target.

Wetting

After spraying and transport, the drop finally hits the target, which, in the case of insecticides and fungicides, is the leaf of the crop. At that time, it faces different barriers that reject water, causing the spray to run off its surface and fall to the ground. The presence of dew, hairiness or high wax deposition, as a result of water stress, aggravate this situation. SpeedAgro has investigated and tested different combinations of surfactants and adhesives in order to determine the most effective mixture when wetting and generating adhesion of the broth on the surface of the sheet.

Inhibition of foam formation

During the incorporation of the assets into the tank and its subsequent agitation, it can generate an overlap of bubbles that will later form the foam.
This generates contamination and losses due to spillage, decreased working autonomy and pulsating flow in the spray, among other undesirable consequences.

There are different foam control agents, including silicone based ones, which quickly disperse through the liquid film that forms the bubble walls. Since silicone has a much lower surface tension (21 mN / m) than most fluids, the surface tension of the film is reduced. The bubbles collapse and the foam disappears.

After a rigorous selection process, the silicones that showed the best response in inhibiting foam formation were identified. Its subsequent incorporation into the formulation allowed obtaining a product with a markedly superior performance. Always incorporate SpeedWet Xion Silicongel at the beginning of the charging process so that foam inhibiting and emulsifying agents work. Keep the agitation or return system running for greater homogenization. Respect the order of loading of the plant protection products to be used.

IMPORTANT
imagen

Siempre incorporar SpeedWet Xion Silicongel al inicio del proceso de carga para que actúen los agentes inhibidores de espuma y emulsionantes.
Mantener el sistema de agitación o de retorno en marcha para una mayor homogeneización.
Respetar el orden de carga de los plaguicidas a utilizar.

INSTRUCTIONS FOR USE
imagen
Preparation: add SpeedWet Xion Silicongel at the beginning of the tank charge (1/4 capacity), complete the tank charge and add the phytosanitary products.

INSTRUCTIONS FOR USE

In insecticide and fungicide applications.

For citrus applications.

DOSE

25-50 cm3 / ha.

25-50 cm3 / 1000 lt.

imagen FOLLETO SpeedWet Xion Silicongel
imagen
SpeedWet Maxion NG is a multi-action soluble concentrate designed to optimize the absorption and biological action of crop protection chemical products.
imagen
GENERAL
imagen

SpeedWet Maxion NG

It is a multi-action adjuvant that improves the activity of the active ingredients of phytosanitary agents, growth regulators, biostimulants and foliar fertilizers when applied to crops. Maximizes the action of the product, since it manages to overcome the physical leaf barriers. It acts as a conditioner for the application vehicle (water), sequestering salts, correcting the pH of the broth to its optimum value.

Salt sequestrant

It sequesters the dissolved salts and chelates the cations in the water, which interfere with the action of the plant protection agents, increasing their activity.

Acidifier

It conditions the pH of the broth to be sprayed for greater and better absorption of the active ingredients used.

Moisturizing action

Reduces the surface tension of spray drops. It allows the product to wet the surface to be treated and to settle evenly, promoting adhesion.

Defoaming action

It has foam controllers, which facilitates the measurement, avoiding spills in the sprayer during the preparation of the application broth. Keep the agitation or return system running for greater homogenization. Respect the order of loading of the plant protection products to be used.

IMPORTANT
imagen

Keep the agitation or return system running for greater homogenization. Respect the order of loading of the plant protection products to be used.

INSTRUCTIONS FOR USE
imagen
Add water to the tank up to ½ or ¾ parts, then add the adjuvant that conditions the water and controls the formation of foam. Finally, incorporate the plant protection products in the correct order.

INSTRUCTIONS FOR USE

Indications for use: in herbicide applications (hormonal, contact, systemic, desiccant, gramicide).

DOSE

75-100 cm3 / 100 lts. Water

(*) según condiciones ambientales y de aplicación.

imagen FOLLETO SpeedWet Maxion
imagen
The action of SpeedWet Antideriva NG modifies the viscosity and elasticity of the broth, causing a narrower spray angle and a higher concentration of impacts on the application target.
imagen
GENERAL
imagen

Speedwet Antideriva NG

It is a liquid adjuvant with a compound formulation specially developed to convey plant protection products in broths for terrestrial and aerial applications. It can be used in place of oil in insecticide, fungicide and herbicide applications. For this purpose, it also has an anti-evaporation effect, which translates into greater treatment efficiency.

Anti-evaporation action

It reduces losses due to volatilization and its high anti-evaporation capacity allows it to be used instead of oils in herbicide, fungicide and insecticide applications.

Surfactant action

It reduces the surface tension of the spray drops, thus achieving a greater degree of uniformity in the coverage.

Moisturizing action

It allows the wetting of the surface to be treated, uniformly depositing the applied product, favoring its distribution.

Anti-drift action

It favors the curtain effect during spraying by producing a fine drizzle of regularly distributed small drops. The agents included in its formulation prevent corrosion of tanks and clogging of pipes and pads.

Defoaming action

Its controlled foam formula allows an adequate action of the pesticide, keeping it in suspension and facilitating its dosage, avoiding losses due to spillage, underdosing and possible residue problems caused by this problem. Keep the agitation or return system running for greater homogenization. Respect the order of loading of the plant protection products to be used.

IMPORTANT
imagen

Keep the agitation or return system running for greater homogenization. Respect the order of loading of the plant protection products to be used.

INSTRUCTIONS FOR USE
imagen
Add water to the tank up to ½ or ¾ parts, add the adjuvant as it conditions the water and controls the formation of foam. Then incorporate the plant protection products in the correct order.

INSTRUCTIONS FOR USE

In insecticide and herbicide applications (hormonal, contact, systemic, desiccant, gramicide)

DOSE

50 c.c. / ha

(*) according to environmental and application conditions.

Is a multi action soluble concentrate specially developed to reduce losses caused by evaporation and drift, as well as to improve the biological action of the phytosanitary products to be used.

imagen FOLLETO SpeedWet Antideriva
imagen
SpeedWet Siliconado NG it is a multi action liquid adjuvant specially developed to carry plant protection products in broths for ground and aerial sprays.
imagen
GENERAL
imagen

SpeedWet Siliconado NG

It can be used in place of oil in insecticide, fungicide and herbicide applications. For this purpose, it also has an anti-evaporation effect, which translates into greater treatment efficiency.

Anti-evaporation action

It reduces volatilization losses and its high anti-evaporation capacity allows it to be used instead of mineral and vegetable oils in graminicide, fungicide and insecticide applications.

Defoaming action

Its controlled foam formula allows an adequate action of the phytosanitary, keeping it in suspension and facilitating its dosage, avoiding losses due to spillage. Keep the agitation or return system running for greater homogenization. Respect the order of loading of the plant protection products to be used.

IMPORTANT
imagen

Keep the agitation or return system running for greater homogenization. Respect the order of loading of the plant protection products to be used.

INSTRUCTIONS FOR USE
imagen
Add water to the tank up to ½ or ¾ parts, then add the adjuvant that conditions the water and controls the formation of foam. Finally, incorporate the plant protection products in the correct order.

INSTRUCTIONS FOR USE

In insecticide and fungicide applications.

In herbicide applications (hormonal, contact, systemic, desiccant, gramicide).

DOSE

50 cm3 / he has

50 - 100 cm3 /he has

(*) according to environmental and application conditions.

imagen FOLLETO SpeedWet Siliconado
imagen
SpeedWet Clean it is a product designed to clean and degas residues of agrochemicals in the sprayer. It also forms a protection film that prevents deposition in walls and the sealing of spikes, pipes, etc.
imagen
GENERAL
imagen

Frequent use of the spraying equipment with chemicals of different formulations causes contamination of the sprayed broth with depositions and phytosanitary residues from previous applications. It is necessary to eliminate these remnants to guarantee the proper functioning of the equipment, the safety of the operator and the rest of the society, and respect of the environment and treated crops, avoiding damage due to phytotoxicity.

The hardness and alkalinity of the water used in the preparation of the application broth, cause gradual wear of the material and the mechanical parts of the sprayer if proper cleaning of the equipment is not carried out after each use. The formation of tartar and the appearance of incrustations on the walls of the spraying equipment reduces the useful life of the equipment significantly, and that is why a good cleaning with an agent that allows the removal of these deposits ensures greater utility of the equipment.

It is here where SpeedWet Clean acts as a DESCRIBER and CLEANING AGENT, guaranteeing an excellent cleaning and maintenance of the equipment.

On the other hand, the application of different phytosanitary products, mainly herbicides (selective, hormonal, etc.) requires adequate cleaning of the spray equipment before being used again, since the impact of inadequate cleaning can be quite problematic and expensive.

Characteristics and properties

+ It is a powerful liquid renewing agent.
+ It has detergent, penetrating, emulsifying and dispersing properties for cleaning tanks.
+ Its formulation gives it descaling and degassing properties that remove and neutralize the remains of chemical products deposited on walls, pipes and spouts.
+ It also has a silicone complex that protects and lubricates the treated surfaces, providing a foam control that facilitates measurement and prevents spillage losses, also favoring rinsing.

IMPORTANT
imagen

Presentation

Box of 12 Liters (12 bottles of 1 liter each). ARGENTINA INDUSTRY

INSTRUCTIONS FOR USE
imagen
Add water to the spray equipment tank until it is half full.
Add SpeedWet Clean according to the recommended dose (see end).
Fill the water volume of the spray equipment tank.
Start the agitator or return system for 10 minutes.
Unload the tank in an appropriate place.
Rinse with clean water.
Important:
The SpeedWet Clean dosage will vary depending on the purpose to be achieved.

INSTRUCTIONS FOR USE

Cleaning agent.

Descaling agent.

Degassing agent.

DOSE

200 cm3 / 200 lts. Water

300 cm3 / 200 lts. Water

500 cm3 / 200 lts. Water

imagen FOLLETO SpeedWet Clean